FSPRO Europe

28/09/2026

𝗔 𝗰𝗹𝗲𝗮𝗻𝗲𝗿 𝘄𝗮𝗹𝗹–𝗳𝗹𝗼𝗼𝗿 𝗷𝘂𝗻𝗰𝘁𝗶𝗼𝗻 𝘄𝗶𝘁𝗵 𝗺𝗼𝗿𝗲 𝗳𝗹𝗲𝘅𝗶𝗯𝗶𝗹𝗶𝘁𝘆 𝗼𝗻 𝘀𝗶𝘁𝗲.

The 𝗙𝗦𝗣𝗥𝗢 𝗙𝟭.𝗦𝟭𝟮𝟭𝟳 + 𝗙𝟭.𝗣𝟮𝟬𝗕 system provides an alternative to conventional projecting skirting boards.

𝗙𝟭.𝗦𝟭𝟮𝟭𝟳 can be installed during wall construction, while the final flooring can be completed later. Once the actual floor level is known, 𝗙𝟭.𝗣𝟮𝟬𝗕 is installed and adjusted to cover the remaining gap.

The result is a clean wall plane without a traditional projecting skirting board - allowing furniture and built-in cabinetry to sit directly against the wall.

𝗙𝟭.𝗣𝟮𝟬𝗕 can also be used independently as a minimal aluminium trim along the floor perimeter.

Two profiles, two approaches to the wall–floor junction.

15/09/2026

𝗙𝗦𝗣𝗥𝗢 𝗶𝘀 𝗴𝗿𝗼𝘄𝗶𝗻𝗴 𝗮𝗰𝗿𝗼𝘀𝘀 𝗘𝘂𝗿𝗼𝗽𝗲 - 𝗰𝗹𝗼𝘀𝗲𝗿 𝘁𝗼 𝗼𝘂𝗿 𝗰𝘂𝘀𝘁𝗼𝗺𝗲𝗿𝘀

We are expanding our network of local distributors to make FSPRO architectural aluminium solutions easier to access, while providing faster communication and local support.

You can currently find our partners in:

🇪🇪 𝗘𝘀𝘁𝗼𝗻𝗶𝗮
OÜ Elektri Ekspert / LedEkspert
www.ledekspert.eu

🇫🇷 𝗙𝗿𝗮𝗻𝗰𝗲
Finitions Plâtre
www.finitionsplatre.fr

🇬🇷 𝗚𝗿𝗲𝗲𝗰𝗲
Lumigo
www.profil-led.gr

🇱🇻 𝗟𝗮𝘁𝘃𝗶𝗮
SIA Poltrona
www.profili.lv

🇲🇰 𝗡𝗼𝗿𝘁𝗵 𝗠𝗮𝗰𝗲𝗱𝗼𝗻𝗶𝗮
Struktural Dizajn
www.structural.mk

🇷🇴 𝗥𝗼𝗺𝗮𝗻𝗶𝗮
Dart Color
+40 762 067 161

Our local partners help architects, interior designers, contractors and customers access FSPRO products closer to their market - including Shadow Gap profiles, concealed skirting systems, recessed curtain tracks, LED profiles and other architectural solutions.

We would like to thank all our partners for their trust and cooperation.

𝗜𝗻𝘁𝗲𝗿𝗲𝘀𝘁𝗲𝗱 𝗶𝗻 𝗯𝗲𝗰𝗼𝗺𝗶𝗻𝗴 𝗮𝗻 𝗙𝗦𝗣𝗥𝗢 𝗱𝗶𝘀𝘁𝗿𝗶𝗯𝘂𝘁𝗼𝗿 𝗶𝗻 𝘆𝗼𝘂𝗿 𝗺𝗮𝗿𝗸𝗲𝘁?
Contact us to discuss B2B cooperation: [email protected]

01/09/2026

30/08/2026

𝗙𝟮.𝟭𝟬 - 𝗼𝗻𝗲 𝗦𝗵𝗮𝗱𝗼𝘄 𝗚𝗮𝗽 𝗽𝗿𝗼𝗳𝗶𝗹𝗲 𝗳𝗼𝗿 𝗳𝗹𝗼𝗼𝗿, 𝘄𝗮𝗹𝗹 𝗮𝗻𝗱 𝗰𝗲𝗶𝗹𝗶𝗻𝗴 𝗱𝗲𝘁𝗮𝗶𝗹𝘀.

Why use a different solution for every junction?

FSPRO F2.10 aluminum profile creates a subtle 10 mm Shadow Gap and can be integrated into different architectural conditions:
→ wall–floor junctions
→ wall–ceiling junctions
→ sloped and changing ceiling planes

This makes it particularly useful in houses with sloped roofs and attic interiors, where vertical walls, angled surfaces and ceilings need to connect through one consistent detail.

At the same time, F2.10 is not limited to residential projects.
Its restrained shadow line works well in 𝗮𝗽𝗮𝗿𝘁𝗺𝗲𝗻𝘁𝘀, 𝗵𝗼𝘁𝗲𝗹𝘀, 𝗼𝗳𝗳𝗶𝗰𝗲𝘀, 𝗿𝗲𝘁𝗮𝗶𝗹 and 𝗰𝗼𝗺𝗺𝗲𝗿𝗰𝗶𝗮𝗹 𝗶𝗻𝘁𝗲𝗿𝗶𝗼𝗿𝘀 where the detail should remain visible without dominating the space.

The profile is designed for gypsum plasterboard systems, so plasterboard build-up, final floor and ceiling levels, finish and transitions should be coordinated before installation.

F2.10 - one compact profile for a continuous architectural line across different surfaces.

24/08/2026

F1.S1060 concealed-mounted aluminium plinth - seamless wall-to-floor integration with optional LED lighting.

A skirting detail does not have to project into the room.

The F1. S1060 concealed-mounted aluminium plinth creates a minimalist wall–floor connection that allows furniture to be placed directly against the wall - without the typical gap created by conventional skirting boards.

The system can be used with MDF decorative inserts 1060 (6 cm), 1080 (8 cm) and 10100 (10 cm), giving designers flexibility in the proportions and final appearance of the plinth.

Key advantages:
→ concealed installation
→ minimalist wall–floor detail
→ no gap between furniture and the wall
→ compatible with MDF decorative inserts in different heights
→ simple fixing with screws, liquid nails or double-sided adhesive tape
→ optional anodizing for increased corrosion resistance and use in humid interiors

And the system is not limited to straight walls.

For projects with curved geometry, we bend both the aluminium F1.S1060 profile and the corresponding MDF insert to the required wall radius. This allows the same plinth concept to continue smoothly across straight and curved surfaces without breaking the architectural line.

A practical solution for residential, hospitality and commercial interiors where detailing, space efficiency and continuity matter.

For custom radii, anodizing or project-specific questions, contact us:
[email protected]

01/08/2026

𝗦𝗵𝗮𝗱𝗼𝘄 𝗚𝗮𝗽: 𝟳 𝘁𝗵𝗶𝗻𝗴𝘀 𝘁𝗼 𝗰𝗼𝗻𝗳𝗶𝗿𝗺 𝗯𝗲𝗳𝗼𝗿𝗲 𝘄𝗼𝗿𝗸 𝗯𝗲𝗴𝗶𝗻𝘀

Most 𝗦𝗵𝗮𝗱𝗼𝘄 𝗚𝗮𝗽 problems are created before installation starts.

Before ordering or fitting the profile, check:

𝟭. 𝗣𝗿𝗼𝗳𝗶𝗹𝗲 𝘀𝗲𝗹𝗲𝗰𝘁𝗲𝗱 𝗯𝗲𝗳𝗼𝗿𝗲 𝗰𝗲𝗶𝗹𝗶𝗻𝗴 𝗹𝗲𝘃𝗲𝗹𝘀 𝗮𝗿𝗲 𝗳𝗶𝘅𝗲𝗱
The profile must match the planned ceiling geometry and installation sequence.

𝟮. 𝗣𝗹𝗮𝘀𝘁𝗲𝗿𝗯𝗼𝗮𝗿𝗱 𝘁𝗵𝗶𝗰𝗸𝗻𝗲𝘀𝘀 𝗰𝗼𝗻𝗳𝗶𝗿𝗺𝗲𝗱
Check board thickness, number of layers and the complete wall or ceiling build-up.

𝟯. 𝗝𝗼𝗶𝗻𝘁𝘀 𝗮𝗻𝗱 𝗲𝗻𝗱𝗶𝗻𝗴𝘀 𝗱𝗼𝗰𝘂𝗺𝗲𝗻𝘁𝗲𝗱
Confirm joints, end points, level changes and transitions to other profiles.

𝟰. 𝗦𝗵𝗮𝗱𝗼𝘄 𝗚𝗮𝗽 𝘄𝗶𝗱𝘁𝗵 𝗮𝗽𝗽𝗿𝗼𝘃𝗲𝗱
Make sure the width suits the room scale, ceiling height and intended visual effect.

𝟱. 𝗟𝗘𝗗 𝘀𝘆𝘀𝘁𝗲𝗺 𝗰𝗼𝗼𝗿𝗱𝗶𝗻𝗮𝘁𝗲𝗱
Check LED-strip width, diffuser, cable route, driver location and maintenance access.

𝟲. 𝗙𝗶𝗻𝗶𝘀𝗵 𝘀𝗽𝗲𝗰𝗶𝗳𝗶𝗲𝗱
Raw aluminium, black, white, RAL or anodised - the decision should be made before ordering.

𝟳. 𝗦𝗶𝘁𝗲 𝘁𝗼𝗹𝗲𝗿𝗮𝗻𝗰𝗲𝘀 𝗰𝗼𝗻𝘀𝗶𝗱𝗲𝗿𝗲𝗱
Check uneven walls, long runs, curves and intersections before installation begins.

A clean 𝗦𝗵𝗮𝗱𝗼𝘄 𝗚𝗮𝗽 detail is not created by the profile alone. It depends on proper coordination between the architect, project manager and installer.

26/07/2026

𝗥𝗔𝗟 𝗼𝗿 𝗡𝗖𝗦? 𝗧𝗵𝗲 𝗿𝗶𝗴𝗵𝘁 𝗰𝗵𝗼𝗶𝗰𝗲 𝗱𝗲𝗽𝗲𝗻𝗱𝘀 𝗼𝗻 𝘁𝗵𝗲 𝗺𝗮𝘁𝗲𝗿𝗶𝗮𝗹.

RAL and NCS are color-reference systems, but they are commonly used with different finishing technologies.

Aluminum Shadow Gap profiles are normally powder-coated.
For this reason, 𝗥𝗔𝗟 is usually the most practical option: powder-coating suppliers offer standard RAL colors in matt, satin, gloss and textured finishes. This provides good durability, repeatability and predictable production costs.

An 𝗡𝗖𝗦 color may also be matched in powder coating, but it is often treated as a custom order and may require additional samples, minimum quantities and a longer lead time.

MDF moldings are normally finished with wet paint or lacquer.
NCS is often preferred because it makes it easier to coordinate the molding with painted walls, doors and other interior elements.

MDF can also be painted in a RAL color.
However, conventional high-temperature powder coating is designed primarily for metal and is not the standard finishing method for MDF.

𝗥𝗲𝗺𝗲𝗺𝗯𝗲𝗿:
the same color code may look different on aluminum and MDF.
Gloss, surface texture, coating type and lighting all influence the final perception.

Never approve an important color only from a display. Use a physical color fan and request samples on the actual materials.

A matching code is a starting point - not a guarantee of a perfect visual match.

23/07/2026

𝗖𝘂𝗿𝘃𝗲𝗱 𝘄𝗮𝗹𝗹𝘀 𝗮𝗿𝗲 𝗻𝗼 𝗿𝗲𝗮𝘀𝗼𝗻 𝘁𝗼 𝗴𝗶𝘃𝗲 𝘂𝗽 𝗼𝗻 𝗦𝗵𝗮𝗱𝗼𝘄 𝗚𝗮𝗽 𝗽𝗿𝗼𝗳𝗶𝗹𝗲𝘀 𝗼𝗿 𝗳𝗹𝘂𝘀𝗵 𝘀𝗸𝗶𝗿𝘁𝗶𝗻𝗴

We adapt our solutions to the geometry of the project.

Shadow Gap profiles, aluminium skirting boards, concealed plinth systems and flush skirting can all be integrated into interiors with curved walls.

Depending on the design, we prepare project-specific aluminium elements and use custom details for complex junctions and transitions.

𝗧𝗵𝗲 𝗿𝗲𝘀𝘂𝗹𝘁:
Continuous architectural lines
Easier and more predictable installation
Better alignment with the original design concept
Consistent detailing across straight and curved walls

The interior should not be simplified because of standard profile limitations.