DJ Machinery Sales

DJ Machinery Sales We buy and sell Tooling New, used and resharpened, Industrial equipment, electric motors and metalworking machinery.

Types of Tooling:
Drill Bits
End Mills
Threading Taps
Reamers
Carbide Inserts
Lathe & Mill Tool Holders
Boring Bars
Plus much much more!

New arrival:C4 Capto shank SECO Tool Holder Grooving / Parting Carbide Insert C4-CFOR-27070-03r230140-JET Indexable tool...
02/01/2022

New arrival:
C4 Capto shank SECO Tool Holder Grooving / Parting Carbide Insert C4-CFOR-27070-03r230140-JET Indexable tooling

New 1-1/2HP Single phase Electric Motor 1ph 1.5HP 1725 RPM 115/230 volts 3/4" Hollow shaft 56CZ USA
01/20/2022

New 1-1/2HP Single phase Electric Motor 1ph 1.5HP 1725 RPM 115/230 volts 3/4" Hollow shaft 56CZ USA

New arrivals
08/16/2021

New arrivals

SOLD 4000 Lb. Capacity Toyota Forklift LP gas 83/189 Mast with sideshift 60" Forks Hard Rubber$7450ConditionUsed - GoodB...
02/13/2021

SOLD 4000 Lb. Capacity Toyota Forklift LP gas 83/189 Mast with sideshift 60" Forks Hard Rubber
$7450

Condition
Used - Good
Brand: Toyota
Model 42-6FGCU20
Year of manufacture 2001?
Lifting Capacity 4050 Lbs. at 20”

Mast 83/189
Mast type FSV
Back Tilt 5

Forks 60”
Serial 80769

Weight 7940 Lbs.
Overall width 42”
Hours: 15,453

Equipped with:
Sideshift
Propane tank
Extra Long forks
Basket mounted to back of cage for storage of chain and other rigging supplies.

Other:
The Magnets, the 2 steel pins on the side of the mast and the chains in photo do not go with it.

Runs fine, it takes about 5 seconds of cranking to get it to start when it’s cold but it always starts, and after that it starts nicely.

Maint performed:
New plugs, wires and dist cap 2014
Tuned up in 2020

This one just arrived.Nachi Fujikoshi PC PCB Printed Circuit Board UM326A and UM301G$485
08/31/2020

This one just arrived.

Nachi Fujikoshi PC PCB Printed Circuit Board UM326A and UM301G
$485

Ergonomic Tool Arms Co. Air Tool Adjustable height Swing arm with Fiam 15C4A Pneumatic screwdriver$3502 piece setI found...
04/26/2020

Ergonomic Tool Arms Co. Air Tool Adjustable height Swing arm with Fiam 15C4A Pneumatic screwdriver
$350

2 piece set

I found a new one of these pneumatic
screwdrivers online New for $1299

This ergonomic arm is also Equipped with a 15C4A Fiam 15C Series Inline 0.25" Hex Pneumatic Screwdriver Auto Shut-Off

The swing arm reaches about 34"

This is for the Ergo arm and the green air tool only, no table is with it, that has already been sold

New arrivals, numerous 3ph & single phase motors, gear reducers and some air motors
03/21/2020

New arrivals, numerous 3ph & single phase motors, gear reducers and some air motors

Address

Walker, MI

Opening Hours

Monday 8am - 5pm
Tuesday 8am - 5pm
Wednesday 8am - 5pm
Thursday 8am - 5pm
Friday 8am - 5pm

Website

Alerts

Be the first to know and let us send you an email when DJ Machinery Sales posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to DJ Machinery Sales:

Shortcuts

Share

Category