Mactool Diamond & Construction Products

Mactool Diamond & Construction Products Quality Diamond & Construction Products
Based in South Africa 🇿🇦
22 Years Experience
Branches in Cape Town, Jhb & Durban

For fabrication, installation, and general construction, accurate hole cutting saves time and material. The Tool‑Co HSS ...
02/06/2026

For fabrication, installation, and general construction, accurate hole cutting saves time and material. The Tool‑Co HSS Bi‑Metal Hole Saws combine hard high‑speed steel cutting edges with a flexible body, giving you improved durability and controlled cutting performance across a wide range of materials. From mild steel and stainless steel to cast iron, copper, aluminium, wood, and plastics, these hole saws deliver clean, chatter‑free holes. The range covers an extensive selection of diameters from 16mm up to 111mm, along with two M14‑compatible arbours (14–30mm and 32–210mm) to support common site and workshop requirements.

🔩 HSS Bi‑Metal Construction – Hard cutting edges paired with a flexible body for lasting durability.
🛠️ Multi‑Material Capability – Cuts mild steel, stainless steel, cast iron, copper, aluminium, wood, and plastics.
📏 Complete Diameter Range – 16, 20, 22, 25, 32, 38, 40, 51, 60, 64, 70, 73, 76, 83, 95, 105, and 111mm.
🔗 Two M14 Arbours Included – Arbour 14–30mm and Arbour 32–210mm for full compatibility.
🎯 Clean, Accurate Cutting – Designed for controlled hole formation with reduced tool chatter.

Get precise holes on every job site.
www.MACTOOL.co.za
021 552 8566 | [email protected]

28/05/2026

Cutting channels for electrical conduit or plumbing pipes through brick and block work takes time when you use a grinder and a chisel. The AGP CG150 Wall Chaser changes that. Its 2500W motor drives a 150mm diamond blade to cut a 47mm wide channel at 50mm deep in a single pass. That is deep enough for standard conduit and pipe recesses without chasing twice. The 22.23mm bore accepts widely available diamond blades, so replacements are easy to find. For electricians and plumbers on South African sites, this machine turns a half‑hour chase into a five‑minute job.

⚡ 2500W Power Input – High‑output motor for aggressive, consistent cutting through masonry.
💎 150mm Diamond Blade – Optimised for channel chasing with smooth, controlled cuts.
📏 50mm Cutting Depth – Deep enough for standard conduit and pipe recesses in one pass.
🛤️ 47mm Channel Width – Creates perfectly sized grooves for electrical and plumbing installation.
🔧 22.23mm Bore – Compatible with widely available diamond blades.

Cut faster, chase cleaner.
www.MACTOOL.co.za
021 552 8566 | [email protected]

26/05/2026

Tackling reinforced concrete, thick masonry, or stone on a site? The KYNKO KD11 is built for the most demanding demolition work. Its 1700W motor delivers 45 Joules of impact energy to smash through the hardest materials without bogging down. The anti‑vibration system keeps you going longer without the usual arm fatigue, and at 11kg the machine is heavy enough to work but light enough to manoeuvre in tight spaces like bathrooms or chases. The SDS‑Max chuck accepts the full range of professional chisels and points, so you are ready for breaking, channelling, or surface prep!

💥 45 Joules Impact Energy – Smashes reinforced concrete, masonry, and stone on site.
⚡ 1700W High‑Efficiency Motor – Sustained power delivery without bogging down.
🛡️ Advanced Anti‑Vibration System – Reduces fatigue for longer, more productive work sessions.
🔩 Professional SDS‑Max Chuck – Secure bit retention with full compatibility for chisels and points.
⚖️ Optimised 11kg Weight – Powerful but manoeuvrable in tight spaces like chases and bathrooms.

Ready to tackle serious demolition? Email or call us for pricing and availability.
www.MACTOOL.co.za
021 552 8566 | [email protected]

From breaking up old foundations in Johannesburg to chasing channels for conduit in Cape Town, the right bit makes all t...
21/05/2026

From breaking up old foundations in Johannesburg to chasing channels for conduit in Cape Town, the right bit makes all the difference. The Tool‑Co SDS Max range covers every common job on South African sites. Choose the Moil point for general demolition, the self‑sharpening Speed point for hard reinforced concrete, or a Wide Chisel in four widths. For soil or clay, the Clay Spade works through wet ground. For surface prep before floor coatings, the Bush Hammer removes laitance and opens up concrete. All bits share an 18mm SDS Max shank and made of steel that handles daily hammering.

🔨 Moil Point – General breaking and demolition. 18 x 400mm.
⚡ Self Sharpening Speed Point – Stays sharper longer for faster pe*******on in hard SA concrete. 18 x 400mm.
🛠️ Wide Chisel – Controlled splitting and chasing. 18 x 400mm. Available in 25, 40, 50, and 75mm widths.
⛏️ Clay Spade – Loosens compacted soil and clay. 18 x 450mm with a 115mm wide blade.
🪨 Bush Hammer – Textures concrete, removes soft top layer, preps for coatings. 18 x 250mm with 16 points.

Match the bit to the job and work faster.
www.MACTOOL.co.za
021 552 8566 | [email protected]

Clean, wet‑cut edges on natural stone start with the right blade. The Tool‑Co range of wet cutting stone blades delivers...
19/05/2026

Clean, wet‑cut edges on natural stone start with the right blade. The Tool‑Co range of wet cutting stone blades delivers professional performance across granite, quartz, and marble, with three dedicated options to match your material. The Silent Centre Granite blade reduces vibration for smoother operation, while the Standard Centre Granite & Quartz blade offers reliable, durable cutting for daily fabrication. For marble and softer stones, the Standard Centre Marble blade provides a clean, chip‑free finish. All three share a 10mm segment height and a 50/60mm bore, ensuring compatibility with most bridge saws and wet cutting equipment.

🔇 Silent Centre Granite – Reduced vibration and noise for smoother, more controlled wet cutting.
🪨 Standard Centre Granite & Quartz – Reliable, durable cutting for everyday stone fabrication.
🪩 Standard Centre Marble – Designed for cleaner, chip‑free cuts on marble and softer stones.
📏 10mm Segment Height – Consistent depth for long‑lasting cutting performance.
🔧 50/60mm Bore – Fits most standard bridge saws and wet cutting machines.
💧 Wet Cutting Optimised – Engineered for water‑cooled cutting to reduce heat and extend blade life.

Cut stone with confidence.
www.MACTOOL.co.za
021 552 8566 | [email protected]

Cutting ultra‑compact ceramic, DEKTON®, Neolith, and Laminam shouldn't mean wrestling with noisy, slow, or short‑lived b...
05/05/2026

Cutting ultra‑compact ceramic, DEKTON®, Neolith, and Laminam shouldn't mean wrestling with noisy, slow, or short‑lived blades. The ADW iKon 25 changes that. Certified and approved for DEKTON® use and perfectly suited for Neolith and Laminam, this Spanish‑made blade delivers superior durability, a clean precise finish, and high cutting speed even at low RPMs. The steel core features an anti‑vibration system that noticeably reduces work noise, while the blade's efficiency means less energy consumption and minimal cutting effort. For bridge saw operators fabricating large‑format slabs, the iKon 25 turns demanding jobs into smoother, faster, and more profitable work.

🇪🇸 Made In Spain – European quality you can trust.
✅ Cuts DEKTON®, Neolith & Laminam – Specifically tested for ultra‑compact ceramics and sintered stone surfaces.
🔇 Anti‑Vibration Core – Reduces noise and stabilises cuts for better control.
⚡ Fast Even At Low Speeds – Maintains aggressive cutting without over‑revving your saw.
💪 Outlasts The Competition – Superior durability means fewer blade changes and lower cost per cut.
💎 Clean, Precise Finish – Minimises chipping for seamless edges and professional results.

Cut smarter, not harder.
www.MACTOOL.co.za
021 552 8566 | [email protected]

On the 1st of May, South Africa joins the world in celebrating Workers' Day, a day to recognise the immense contribution...
01/05/2026

On the 1st of May, South Africa joins the world in celebrating Workers' Day, a day to recognise the immense contribution of every person who labours with skill, dedication, and pride. From the electrician chasing walls at dawn to the tiler finishing a floor at dusk, from the stone fabricator shaping countertops to the concrete finisher smoothing massive slabs: your work shapes our homes, our roads, our hospitals, and our future. At MACTOOL, we see your effort every single day, and we salute you!

🛠️ Your Skill – Every cut, every joint, every polished surface reflects years of craft and care.
🧱 Your Grit – Rain or shine, you show up and get the job done right.
🏗️ Your Safety – We wish you hazard‑free sites and smooth‑running equipment.
🇿🇦 Your Value – Your labour is the foundation of South Africa's growth.
🔨 Your Rest – Take this day to step back, recharge, and be proud of what you do.

Thank you for building our nation, one job at a time.
www.MACTOOL.co.za
021 552 8566 | [email protected]

29/04/2026

Routing channels for conduit and pipework just got more efficient with the AGP CG150 Wall Chaser, delivering 2500W of power to drive 150mm diamond blades, cutting channels up to 50mm deep and 47mm wide in a single pass. Built for professional electricians and plumbers, this machine creates straight, uniform grooves with reduced dust and fewer passes, saving time on every job site. The 22.23mm bore accepts standard diamond blades, and the robust construction stands up to daily masonry chasing work.

⚡ 2500W Power Input – High-output motor for aggressive, consistent cutting through masonry.
💎 150mm Diamond Blade – Optimised for channel chasing with smooth, controlled cuts.
📏 50mm Cutting Depth – Deep enough for standard conduit and pipe recesses in one pass.
🛤️ 47mm Channel Width – Creates perfectly sized grooves for electrical and plumbing installation.
🔧 22.23mm Bore – Compatible with widely available diamond blades.

Take the hard work out of wall chasing.
www.MACTOOL.co.za
021 552 8566 | [email protected]

On the 27th of April, South Africa marks the day democracy was born, the day every citizen gained the right to vote and ...
27/04/2026

On the 27th of April, South Africa marks the day democracy was born, the day every citizen gained the right to vote and a voice in our nation's future! Freedom Day commemorates the first democratic elections in 1994, a peaceful transition that changed our country forever. At MACTOOL, we honour that spirit of progress and unity. Just as we provide the tools to build and shape physical structures, we recognise the ongoing work of building a free, fair, and flourishing South Africa for generations to come.

🇿🇦 Remembering 1994 – The first democratic elections that changed our nation forever.
🤝 Unity In Diversity – Celebrating the spirit of togetherness that defines South Africa.
🔨 Building The Future – Honouring the work of every South African shaping tomorrow.
📅 27 April – A day of reflection, gratitude, and hope.
❤️ Proudly South African – Committed to growth, fairness, and opportunity for all.

Wishing you a meaningful Freedom Day from all of us at MACTOOL.
www.MACTOOL.co.za
021 552 8566 | [email protected]

Address

Unit 6 Pennisi Park, 3 Jig Avenue, Montague Gardens
Cape Town
7441

Opening Hours

Monday 08:00 - 17:00
Tuesday 08:00 - 17:00
Wednesday 08:00 - 17:00
Thursday 08:00 - 17:00
Friday 08:00 - 16:00

Website

Alerts

Be the first to know and let us send you an email when Mactool Diamond & Construction Products posts news and promotions. Your email address will not be used for any other purpose, and you can unsubscribe at any time.

Contact The Business

Send a message to Mactool Diamond & Construction Products:

Shortcuts

Share